Whisper-quiet, efficient and easy to use
The necessary power is provided by two 2-channel Class D power amplifiers optimally tuned to the I-Line column speakers – the IA 202D with 2x 250 W at 8 Ω and the IA 402D with either 2x 200 W at 8 Ω or 2x 400 W at 4 Ω.
The built-in 24bit/48kHz DSP processor supplies all I-Line speakers with customised and precise filter, EQ and limiter settings. A rotary push-button on the front panel conveniently controls pre-set speaker presets, delay and other functions. This ensures fast, uncomplicated and carefree system setup and tuning.
Both amplifiers operate the speakers remarkably quietly – made possible by a sensor-controlled fan, an aerodynamically optimised front to back airflow, and a very low idle power. Ideal for quiet environments!
The I-Line amplifiers are equipped with the three most common analogue input and output connectors. 2-channel XLR inputs with link outputs in conjunction with Phoenix MSTB 3-pin inputs cover the majority of all input requirements. Maximum flexibility at the outputs is provided by 3x Neutrik speakON® connectors in parallel to 4-pin Phoenix MSTB connectors.
IA 202D power amplifier is equipped with 3 most widely used analog input and output connections in professional audio. 2 channel XLR inputs with link outputs together with Phoenix MSTB 3-pin inputs will cover most of the input needs. Outputs are equipped with 3x Neutrik speakON® connectors in parallel with 4-pin Phoenix MSTB connectors for maximum flexibility.
24bit/48kHz DSP processor provides all I-line speakers with correct and precise filter, EQ and limiter settings. As always - good sounding and well protected speaker systems are the ultimate aim of the SE AUDIOTECHNIK engineering team. Built-in speaker presets, EQ control, delay and other features allow for an easy, cost-effective and quick system setup and tuning.
I-Line Review in Produciton Partner Magazine
With the I-Line, the Solingen-based manufacturer SE Audiotechnik presents a series of compact loudspeakers with sets consisting of two tops in column design, two DSP amplifiers and an active 12” subwoofer. How will this combination perform in fixed installations?
|Type:||Class-D, Switched Mode Power Supply|
|Rated Output Power (1kHz, THD: <1%) *:|| 2 x 250 W @ 8 Ω |
2 x 150 W @ 16 Ω
|Minimum load impedance:||8 Ω|
|Damping factor:||> 200|
|Input impedance:||10 kΩ balanced/unbalanced|
|Maximum input level:||+20 dBu|
|SNR Line in to Spk out:||90 dB|
|Noise Floor:||-52 dBu (A-weighted) @4 dBu sensitivity, 0 dB master attenuation|
|Channel crosstalk:||64 dB|
|THD+N:||< 0.1% @ 1 W,1 KHz; < 0.3% @ 1 dB below rated power|
|DSP:|| 48 kHz/24 bit DSP processor |
Processing latency: 1.1 ms
|Protection:||Short circuit, overheating, overcurrent|
|Cooling:|| Sensor controlled fan |
Front-to-Back air flow
|Power efficiency:||Up to 76%|
|Power consumption:|| Idle: 29 W |
Full Power: 600 W
|Operating voltage range:||100 – 240 VAC 50/60 Hz|
|Screen:||LCD, 4x20 symbol alpha-numeric|
|User controls:||Control encoder with push-button, Power On|
|Input signal connectors:|| XLR-3 female line-level inputs |
XLR-3 male link outputs
Phoenix MSTP 3-pin inputs and link outputs
|Output signal connectors:|| Neutrik SpeakON® NL4 outputs |
Phoenix Contact MSTB 4-Pin outputs
|Power connector:||IEC C14|
|DSP Features:||Levels, Parametric EQ, Delay, Phase, Input sensitivity, RMS limiter, Peak limiter, IIR/FIR filtering|
|Configuration handling:|| Loading of factory presets provided by SE |
Saving and recalling of user presets
|Product dimensions [H x W x D]:||66 x 483 x 256 / 1.5 RU|
|Net weight:||4.7 kg|
|Packaging dimensions [H x W x D]:||143 x 588 x 380 mm|
|Total weight::||7.25 kg|
|Cabinet:||Aluminium front panel, steel body|
|Rack mounting:||Four frontal 6 mm holes at both sides|
|Operating temperature range:||[0°C ; 40°C]|
|Storage temperature range:||[-40°C ; 70°C]|
|All product specifications are subject to change without prior notice||* According to IHF-A-202.|