LA 10.4D
This dedicated system amplifier was designed for maximum ease of operation, versatility and control, when powering the L-Line line array systems.
The amplifier has high-quality integrated DSP processing, Dante® networked-audio and remote network control. Most importantly there are system tuning and optimization tools at your fingertips such as parametric EQ, delay and FIR filtering.
LA 10.4D is a four-channel system amplifier with a power output of 4x 2.570W per channel. The 4 Ω minimum impedance support allows for a large number of speakers to be connected.
Dedicated software for planning, analyzing and executing your application will be available in the future. With an intuitive user interface, professional audio toolkit and comprehensive network control, you’ll be able to optimize your workflow as well as save time and money.
Max. configuration:
1x LA 10.4D (4 channel mode)
16x L 35 (4 pieces / channel)
Features
Connectivity
LA 10.4D power amplifier is equipped with 3 most widely used analog input and output connections in professional audio. 2 channel XLR inputs with link outputs together with Phoenix MSTB 3-pin inputs will cover most of the input needs. Outputs are equipped with 3x Neutrik speakON® connectors in parallel with 4-pin Phoenix MSTB connectors for maximum flexibility.
Integrated DSP
24bit/48kHz DSP processor provides all L-line speakers with correct and precise filter, EQ and limiter settings. As always - good sounding and well protected speaker systems are the ultimate aim of the SE AUDIOTECHNIK engineering team. Built-in speaker presets, EQ control, delay and other features allow for an easy, cost-effective and quick system setup and tuning
Related Products
Specifications
Model: | |
---|---|
ELECTRICAL | |
Type: | Networked DSP amplifier with 4x BTL Class D and Switch Mode Power Supply |
Channels: | Four |
Output Power*: | 4 x 1200 W @ 8 Ω, 1 kHz, 1%THD 4 x 1390 W @ 8 Ω, 1 kHz, 2%THD 4 x 1720 W @ 4 Ω, 1 kHz, 1%THD 4 x 2570 W @ 4 Ω, 1 kHz, 2%THD 4 x 1460 W @ 8 Ω, 50 Hz, 4%THD 4 x 1550 W @ 4 Ω, 50 Hz, 4%THD |
Minimum load impedance: | 4 Ω |
Frequency response (Line In) (4 Ω): | 20 Hz to 20 kHz: -1 dB |
Damping factor: | 8 Ω: > 500 @ 1 kHz 4 Ω: > 250 @ 1 kHz |
Input impedance: | > 20 kΩ balanced |
Maximum input level: | +23 dBu |
SNR Line In to Spk out: | 110,7 dB, 113,5 dB(A) (@1500 W/8 Ω, +42 dBu) |
Noise Floor: | -68,7 dBu (280 uV), -71,5 dBu(A) (200 uV(A)) |
Channel crosstalk: | -97,8 dB |
THD+N: | < 0.0087% at 175 W into 4 Ω (1/8th of Rated Power) < 0.0095% at 350 W into 4 Ω (1/4th of Rated Power) |
DSP: | 48/96 kHz, 32 bit SHARC CPU with floating point processing |
System latency: | 1 ms to 10 ms (preset dependent) |
Protection: | Short circuit, overheating, overcurrent |
Cooling: | Two fans with temperature dependant speed and tacho feedback Front-to-back air flow |
Power efficiency: | Up to 76% |
Power consumption (both PowerCON® summed): | Off: 3 W Idle: 70 W at 1/8 of Rated power: 1000 W at 1/4 of Rated power: 2000 W at 1/3 of Rated power: 2666 W Peak power: 8000 W |
Inrush current (per PowerCON®): | 40 A (<1 ms) when connected to mains 9 A (<250 ms) when switching on |
Operating voltage range: | 90 – 265 VAC 50/60 Hz |
HARDWARE | |
Indicators: | 4x Input signal level Led: -30dB, -12dB, -6dB, Clip 4x Channel Led: Mute, Active, -30dB, -12dB, -6dB, Limit, Protect 6x Status Led: Dante, AES1+2, AES3+4, LAN, Stand-By, Fault |
Screen: | 3.5" TFT Color display with Touch Panel & 320 x 240 resolution RGB |
User controls: | Control encoder with push-button Touch Screen 4x channel MUTE Power On - Power On |
Input signal connectors: | 4x XLR-3 male line-level inputs and buffered link outputs 2x XLR-3 male AES/EBU inputs and buffered link outputs 1x Dante® Ultimo 4ch input via separate etherCON terminal 1x Network control via separate etherCON terminal 1x Front USB |
Output signal connectors: | 4x Neutrik SpeakON® NL4 outputs |
Power connector: | 2x Neutrik PowerCON® 20 A |
SOFTWARE | |
DSP Features: | Levels, Parametric EQ, Delay, Phase, RMS Limiter, Peak Limiter, IIR/FIR Filtering |
Configuration handling: | Loading of factory presets provided by SE Audiotechnik® Saving and recalling of user presets |
Remote control via network: | Controlling of individual amplifiers or parameter-groups in distributed amplifiers via desktop software Configuring of arbitrary numbers of amplifiers with parameters resulting from venue-sound field simulations |
Monitoring: | Temperatures Fan speeds Voltages Connection states Fault states System events Runtime |
MECHANICAL | |
Product Dimensions [H x W x D]: | 89 x 483 x 480 mm / 2 RU |
Net weight: | 14.5 kg |
Packaging dimensions [H x W x D]: | 143 x 588 x 380 mm |
Total weight: | 7.65 kg |
Cabinet: | Aluminum front panel, steel housing |
Rack mounting: | Four frontal 6 mm holes at sides |
Operating ambient temperature range: | [5°C ; 40°C] |
Storage temperature range: | [-20°C ; 90°C] |
Ingress Protection: | IP20 |
All product specifications are subject to change without prior notice. | * According to CEA-2006. |